===== Turn in-house FR-X OFF =====

----

==== Detector ====

Open Firefox and connect to 192.168.127.50

{{:crystallography:collection:frx:framegrabber_1.png?600|}}

Select 'system settings'. Username = eiger, PW = #EIGER_Detector#

In the lefthand column select 'EIGER' and then 'DCU-Control'

{{:crystallography:collection:frx:framegrabber_2.png?600|}}

select "Power OFF" to shut down the framegrabber.

{{:crystallography:collection:frx:framegrabber_3.png?600|}}

Switch OFF the power supply for the EIGER.

{{:crystallography:collection:frx:eiger_power_supply.jpg?600|}}

Switch OFF the EIGER water chiller.

{{:crystallography:collection:frx:eiger_chiller.jpg?400|}}

----

==== FR-X ====

Decrease gradually the the current 66 to 10 mA and then voltage from 45 kV to 20 kV. First step 66->60 mA, (45->40 kV). Wait 10 s. Then decrease by steps of 10. (Lower the current first.)

{{:crystallography:collection:frx:xg.png?600|}}

Turn X-RAY OFF on the XG Control panel. Wait 1h.

Stop the Vacuum on the XG Control panel. Wait 1h.

POWER OFF on the FR-X main panel.

{{:crystallography:collection:frx:frx_front.jpg?600|}}

Switch OFF at the back of the FR-X.

{{:crystallography:collection:frx:frx_back.jpg?400|}}

Switch the main power source OFF.

{{:crystallography:collection:frx:main_power_supply.jpg?600|}}

Switch OFF AFC-11 Goniometer controller.

{{:crystallography:collection:frx:afc11_closeup.jpg?600|}}

Switch OFF the two fans of AFC-11.

{{:crystallography:collection:frx:acf11_back.jpg?400|}}

Switch OFF the vacuum pump below the Cobra Controller.

{{:crystallography:collection:frx:pump1.jpg?250|}}
{{:crystallography:collection:frx:pump1_closeup.jpg?250|}}

Switch OFF the vacuum pump below the BioSAXS.

{{:crystallography:collection:frx:pump2.jpg?250|}}
{{:crystallography:collection:frx:pump2_closeup.jpg?350|}}

----

==== Cryostream ====

On the Cobra Controller :

{{:crystallography:collection:frx:cobra_front.jpg?600|}}

  * Program / Ramp (change with dial) / Enter
  * Choose the speed (up to 360K/h) / Enter
  * Target / 293 K (Ambient) / Enter
  * Start
  * When ambient temperature is reached, press Stop

Switch OFF at the back.

{{:crystallography:collection:frx:cobra_back.jpg?600|}}

Switch OFF the helium compressor.

{{:crystallography:collection:frx:helium.jpg?300|}}
{{:crystallography:collection:frx:helium_back.jpg?250|}}

----

==== Technical Room E0044 ====

{{:crystallography:collection:frx:technical_room.jpg?400|}}

Switch OFF the nitrogen compressor using the touch panel.
Switch OFF the compressor on the back of the device.

{{:crystallography:collection:frx:n2.jpg?150|}}
{{:crystallography:collection:frx:n2_closeup.jpg?400|}}

Switch OFF the main switch of the water cooling device (Haskins).

{{:crystallography:collection:frx:haskins.jpg?200|}}
{{:crystallography:collection:frx:haskins_closeup.jpg?400|}}

Close the water supply. (red valve)

{{:crystallography:collection:frx:red_valve.jpg?400|}}

----

==== EIGER Computer ====

Shut down the computer.

{{:crystallography:collection:frx:pc.jpg?600|}}

----

==== BioSAXS ====

Switch OFF

{{:crystallography:collection:frx:saxs_control_1.jpg?600|}}

Switch OFF at the back.

{{:crystallography:collection:frx:saxs_control_2.jpg?600|}}

Remove the small middle screw to access the Pilatus 100K detector and switch OFF.

{{:crystallography:collection:frx:pilatus100k_cover.jpg?200|}}
{{:crystallography:collection:frx:pilatus100k.jpg?400|}}

----

==== BioSAXS Computers ====

Shut down the SAXS PC.

{{:crystallography:collection:frx:saxs_pc.jpg?600|}}

Switch the display and control to the framegrabber with the Switch.

{{:crystallography:collection:frx:saxs_pc_switch.jpg?400|}}

Shut down the SAXS framegrabber.